- Beranda
- Sparepart Motor
- Suspensi / Rearset / Velg / Swingarm
- Swingarm
- GM-MOTO
- GM-MOTO: Swingarm Aluminium Tipe G
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
Dibuat di China
Manufaktur: KEPSPEED Made in China
Manufacturer: KEPSPEED
Manufaktur: KEPSPEED Made in China
Manufacturer: KEPSPEED
[Deskripsi]
Ini adalah model standar pipa bagian heksagonal ekstra tebal!
Ini adalah model standar tipe G yang membuat KEPSPEED terkenal.
Ini menggunakan pipa penampang heksagonal dan menggunakan bantalan jarum di bagian poros, yang merupakan spesifikasi tanpa kompromi.
Ada empat tipe ekstensi : + 6cm, + 12cm, + 16cm, dan + 20cm.
• Ini mengadopsi bantalan jarum untuk bagian poros
• Penjualan terbesar! Ini menggunakan pipa penampang
• Ini adalah penyetel rantai yang sudah dikenal. Standard model with extra thick hexagonal triple-square section pipe!
This is the standard model of Type G that has made KEPSPEED famous.
No compromises have been made with the use of hexagonal triple-sectioned pipes and needle bearings in the pivot section.
There are four types of extension: +6cm, +12cm, +16cm and +20cm.
●Needle bearings are used in the pivot section
●The biggest selling point!Adopted a pipe with the twin-square section
●This is a familiar chain adjuster.
Ini adalah model standar tipe G yang membuat KEPSPEED terkenal.
Ini menggunakan pipa penampang heksagonal dan menggunakan bantalan jarum di bagian poros, yang merupakan spesifikasi tanpa kompromi.
Ada empat tipe ekstensi : + 6cm, + 12cm, + 16cm, dan + 20cm.
• Ini mengadopsi bantalan jarum untuk bagian poros
• Penjualan terbesar! Ini menggunakan pipa penampang
• Ini adalah penyetel rantai yang sudah dikenal. Standard model with extra thick hexagonal triple-square section pipe!
This is the standard model of Type G that has made KEPSPEED famous.
No compromises have been made with the use of hexagonal triple-sectioned pipes and needle bearings in the pivot section.
There are four types of extension: +6cm, +12cm, +16cm and +20cm.
●Needle bearings are used in the pivot section
●The biggest selling point!Adopted a pipe with the twin-square section
●This is a familiar chain adjuster.
Catatan
* Gambar hanya untuk referensi. Gambar yang ditampilkan mungkin berbeda dari produk yang sebenarnya.
Peringatan
* Lengan ayun ini adalah produk KEPSPEED yang memproduksi suku cadang aluminium berkualitas tinggi.
* Sehubungan dengan penginstalan
Ini menggunakan poros poros OEM tetapi disarankan untuk menggunakan panjang poros bawah panjang kepala 215mm M12 panjang untuk tujuan keamanan.
Poros poros panjang dijual terpisah.
Sehubungan dengan diameter roda yang dapat dipasang untuk setiap jenis ekstensi, ini bervariasi tergantung pada kombinasinya, seperti flat rate atau lebar roda ban yang akan digunakan.
Silakan menilai itu oleh pelanggan dengan mengacu pada foto ukuran.
Selain itu, kami sedang memeriksa pemasangan roda lebar hingga 4.0J.
Namun, ini membutuhkan penyetelan posisi tengah roda, penyetelan garis rantai, penyetelan posisi bagian yang berhubungan dengan rem, dll.
Penyesuaian ini berbeda tergantung pada kondisi tubuh pelanggan dan hubungannya dengan bagian lain yang akan digunakan.
Mohon maaf atas ketidaknyamanan terkait metode penyesuaian ini karena akan ditanggung oleh pelanggan.
Selain itu, perlu diketahui bahwa pemisahan yang aman seperti yang direkomendasikan oleh produsen sepeda motor tidak akan terjamin.
Panjang keseluruhan lengan ayun memerlukan ekstensi rantai penggerak dengan cara diperpanjang.
Kami tidak memandu perusahaan GM-MOTO karena jumlah rangka dalam rantai penggerak akan bervariasi tergantung pada kondisi tubuh pelanggan dan sprocket di sekitar dan di belakang.
Selain itu dapat mengganggu seperti ban dan spatbor tergantung spesifikasi bodi kendaraan (oleh pelanggan).
Harap pastikan untuk memeriksa apakah ada titik kontak yang tidak normal sebelum berkendara meskipun suspensi belakang dalam kondisi dasar penuh.
Harap lakukan proses untuk mengurangi celah dengan mesin cuci atau lainnya jika jarak antara rangka Anda dan lengan ayun ini 0,5 mm atau lebih di setiap sisi
Ini memiliki beban tinggi pada lengan ayun, dan dalam kasus terburuk dapat rusak saat poros pivot dikencangkan sementara jarak bebasnya besar.
Harap perhatikan terjadinya apa yang disebut kelonggaran awal setelah mulai berjalan, dan harap sering melakukan inspeksi agar tidak menimbulkan masalah yang tidak terduga.
* Sehubungan dengan garansi
Ada kasus yang memiliki goresan kecil karena masalah transportasi.
Itu tidak tercakup dalam garansi kecuali untuk cacat yang secara signifikan merusak nilai atau fungsi produk.
Produk RETURN tidak dapat diterima untuk alasan apapun.
Selain itu, masalah setelah mulai mengemudi sering disebabkan oleh situasi mengemudi, situasi pemeliharaan, atau ketidaksesuaian dengan kondisi bodi mobil, sehingga sulit membedakannya dari penyebab masing-masing produk, jadi kami akan menganggapnya sebagai pengecualian sepenuhnya. [Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*This swingarm is a product of KEPSPEED, a manufacturer of high quality aluminum parts.
※ About installation
Stock axle shafts can be used, but it is recommendable to use 215mm M12 long shafts for safety.
Long axle shafts are available separately.
The mountable wheel diameters for each extension type vary depending on the combination of flatness and wheel width of the tire used.
Please refer to the size image and judge by yourself.
Also, the installation of wide wheels up to 4.0J are comfirmed.
However, it is necessary to adjust the center position of the wheel, the chain line, and the position of the brake related parts.
This adjustment method varies depending on the condition of the customer's vehicle and the relationship with other parts used.
You will be responsible for these adjustments.
Also, please note that it does not ensure a safe separation as recommended by the motorcycle manufacturer.
Due to the extended swingarm length, the drive chain needs to be extended.
The number of frames of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
In addition, depending on the specifications of the customer's vehicle, the tires may come in contact with the fender or other parts of the vehicle.
Even when the rear suspension is at full bottom, be sure to check for any abnormal contact points before driving.
If there is a gap of 0.5mm or more between the frame and the swingarm, please use washers to reduce the gap.
If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
After the start of driving, pay attention to the occurrence of so-called "initial loosening" and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
*There may be changes in product specifications due to the manufacturer's reasons.
* Sehubungan dengan penginstalan
Ini menggunakan poros poros OEM tetapi disarankan untuk menggunakan panjang poros bawah panjang kepala 215mm M12 panjang untuk tujuan keamanan.
Poros poros panjang dijual terpisah.
Sehubungan dengan diameter roda yang dapat dipasang untuk setiap jenis ekstensi, ini bervariasi tergantung pada kombinasinya, seperti flat rate atau lebar roda ban yang akan digunakan.
Silakan menilai itu oleh pelanggan dengan mengacu pada foto ukuran.
Selain itu, kami sedang memeriksa pemasangan roda lebar hingga 4.0J.
Namun, ini membutuhkan penyetelan posisi tengah roda, penyetelan garis rantai, penyetelan posisi bagian yang berhubungan dengan rem, dll.
Penyesuaian ini berbeda tergantung pada kondisi tubuh pelanggan dan hubungannya dengan bagian lain yang akan digunakan.
Mohon maaf atas ketidaknyamanan terkait metode penyesuaian ini karena akan ditanggung oleh pelanggan.
Selain itu, perlu diketahui bahwa pemisahan yang aman seperti yang direkomendasikan oleh produsen sepeda motor tidak akan terjamin.
Panjang keseluruhan lengan ayun memerlukan ekstensi rantai penggerak dengan cara diperpanjang.
Kami tidak memandu perusahaan GM-MOTO karena jumlah rangka dalam rantai penggerak akan bervariasi tergantung pada kondisi tubuh pelanggan dan sprocket di sekitar dan di belakang.
Selain itu dapat mengganggu seperti ban dan spatbor tergantung spesifikasi bodi kendaraan (oleh pelanggan).
Harap pastikan untuk memeriksa apakah ada titik kontak yang tidak normal sebelum berkendara meskipun suspensi belakang dalam kondisi dasar penuh.
Harap lakukan proses untuk mengurangi celah dengan mesin cuci atau lainnya jika jarak antara rangka Anda dan lengan ayun ini 0,5 mm atau lebih di setiap sisi
Ini memiliki beban tinggi pada lengan ayun, dan dalam kasus terburuk dapat rusak saat poros pivot dikencangkan sementara jarak bebasnya besar.
Harap perhatikan terjadinya apa yang disebut kelonggaran awal setelah mulai berjalan, dan harap sering melakukan inspeksi agar tidak menimbulkan masalah yang tidak terduga.
* Sehubungan dengan garansi
Ada kasus yang memiliki goresan kecil karena masalah transportasi.
Itu tidak tercakup dalam garansi kecuali untuk cacat yang secara signifikan merusak nilai atau fungsi produk.
Produk RETURN tidak dapat diterima untuk alasan apapun.
Selain itu, masalah setelah mulai mengemudi sering disebabkan oleh situasi mengemudi, situasi pemeliharaan, atau ketidaksesuaian dengan kondisi bodi mobil, sehingga sulit membedakannya dari penyebab masing-masing produk, jadi kami akan menganggapnya sebagai pengecualian sepenuhnya. [Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*This swingarm is a product of KEPSPEED, a manufacturer of high quality aluminum parts.
※ About installation
Stock axle shafts can be used, but it is recommendable to use 215mm M12 long shafts for safety.
Long axle shafts are available separately.
The mountable wheel diameters for each extension type vary depending on the combination of flatness and wheel width of the tire used.
Please refer to the size image and judge by yourself.
Also, the installation of wide wheels up to 4.0J are comfirmed.
However, it is necessary to adjust the center position of the wheel, the chain line, and the position of the brake related parts.
This adjustment method varies depending on the condition of the customer's vehicle and the relationship with other parts used.
You will be responsible for these adjustments.
Also, please note that it does not ensure a safe separation as recommended by the motorcycle manufacturer.
Due to the extended swingarm length, the drive chain needs to be extended.
The number of frames of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
In addition, depending on the specifications of the customer's vehicle, the tires may come in contact with the fender or other parts of the vehicle.
Even when the rear suspension is at full bottom, be sure to check for any abnormal contact points before driving.
If there is a gap of 0.5mm or more between the frame and the swingarm, please use washers to reduce the gap.
If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
After the start of driving, pay attention to the occurrence of so-called "initial loosening" and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
*There may be changes in product specifications due to the manufacturer's reasons.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/